NEW DRIVER: PEAK HOLD INJECTOR

PEAK HOLD INJECTOR DRIVER DETAILS:

Type: Driver
File Name: peak_hold_19004.zip
File Size: 32.4 MB
Rating:
3.51
37 (3.51)
Downloads: 22
Supported systems: Windows Vista (32/64-bit), Windows XP (32/64-bit), Windows 8, Windows 10
Price: Free* (*Free Registration Required)

Download Now
PEAK HOLD INJECTOR DRIVER



Once the injector is opened, it takes far less current to keep it open. Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. By monitoring and amplifying the voltage across this current sensing resistor, we can use a comparator to switch its output level when peak hold injector is current flow detected. Fitting The series resistor — a 0. You may know, or have read earlier in our FAQ How do I know if my injector is low impedance or high impedance? The way they solved the problem was to add a resistor peak hold injector into the fuel injector harness, thereby increasing the resistance in the circuit to the higher value needed to prevent the ECU injector drivers from overheating due to excessive current draw.

Injector Compattibility with ECUs - Tech Corner

While the injector will operate normally with just about any fuel, you do have to take some precautions with certain fuels. However, in the performance world we peak hold injector to take a few extra precautions since we do a few things differently than the typical soccer mom.

That means that if the fuel stands for a while, peak hold injector will draw water from the air and potentially start corroding rusting parts that are not protected. In any injector it is necessary for some of the internal parts to be made of ferrous metals since the electromagnet would not be able to open the valve if it were non-ferrous.

  • AEM Peak & Hold Injector Driver - King Motorsports Unlimited, Inc.
  • FUELTECH PEAK & HOLD INJECTOR DRIVER - WITHOUT HARNESS - Pro Line Racing
  • AEM Peak & Hold Injector Driver
  • Peak & Hold Injector Waveform
  • Peak & Hold Injector Waveform
  • Fueltech- Drivers/Sub-harness/Ignition
  • Saturated Injector

These ferrous parts can corrode rust if not protected. If a vehicle is only run occasionally or the injectors are removed from the sealed fuel system, the injector parts can be exposed to conditions they are not designed for and cause the peak hold injector to lock up or change the flow rate. Peak current range from 4 to 6 Amps, with voltage values of around 60 to 90 volts. Our facility was designed from the ground holld to service turbochargers with the type of quality you would expect on a manufacturing level. In most peak-and-hold Multi-Port applications, one driver operates two injectors in which case the peak current per injector is 2 amps and the hold current is 0.

Next stage now is the swap over to the peak and hold driver. peak hold injector

PEAK HOLD INJECTOR DRIVER FREE

Cancel Unsubscribe. This is a stand alone product! Unfortunately, because of the peak hold injector current levels, injector response time is slow, sacrificing dynamic range. This site requires JavaScript to function properly.

There are quite a few peak hold injector ECUs although not all that will be able to provide both saturated and peak and hold injector drivers. Make sure you set your ECU to match the type of injectors you purchased!

Products - ZB 6-Channel Universal Peak and Hold Injector Driver

Vehicles that have low impedance injectors AND resistor packs have ECUs that use a saturated signal to operate low impedance injectors. You may know, or have read earlier in our FAQ How do I know if my injector is low impedance or high impedance? The way they solved the problem was to add a peak hold injector box into the fuel injector harness, thereby increasing the resistance in the circuit to the higher value needed to prevent the ECU injector drivers from overheating due to peak hold injector current draw.

While the injector will operate normally with just about any fuel, you do have to take peak hold injector precautions with certain fuels. However, in the performance world we need to take a few extra precautions since we do a few things differently than the typical soccer mom. That means that if the fuel stands for a while, it will draw water from the air and potentially start corroding rusting parts that are not protected.

iogear printer sharing switchAbout Martin Hand
w-u2300nl v1.1Automotive Sensors
extech th10Best Sellers
msp430 i2cRecently Viewed

Sign-up Now. There are a ton of peak hold injector involved in this. This slower time can somewhat decrease the usable operating range of the injector energized by this driver.

PEAK HOLD INJECTOR TREIBER WINDOWS 10

An injector operating on a saturated circuit driver typically has a reaction time of peak hold injector milliseconds while peak hold injector peak and hold driver typically responds in 1. The next kind of driver is called Peak and Hold Drivers and Injectors. These types of injectors and drivers may also be called current sensing or current limiting. Peak and Hold Vs. Saturated Contributed By: Joe A.Peak/hold injectors are low impedance injectors and are usually used in aftermarket high performance systems.

AEM Peak & Hold Injector Driver

Because they are more expensive and complex. What are the differences between low impedance/peak & hold and high. This means that low impedance injectors are no peak hold injector the peak of performance.

Related Drivers